Ordering no:
Cable plug connector with cable clamp, shieldable, cable outlet 6-8 mm
Cable plug connector with cable clamp, shieldable, cable outlet 6-8 mm, Series 581
Available numbers of contacts
99 2001 20 02
M16 IP40 cable connector, Contacts: 2, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2001 20 02
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 7 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 27.549 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2001 29 02
M16 IP40 cable connector, Contacts: 2, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2001 29 02
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 7 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 27.549 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2005 20 03
M16 IP40 cable connector, Contacts: 3 DIN, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2005 20 03
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 7 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 27.778 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2005 29 03
M16 IP40 cable connector, Contacts: 3 DIN, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2005 29 03
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 7 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 27.778 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2009 20 04
M16 IP40 cable connector, Contacts: 4, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2009 20 04
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 6 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 27.989 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2009 29 04
M16 IP40 cable connector, Contacts: 4, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2009 29 04
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 6 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 27.998 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2013 20 05
M16 IP40 cable connector, Contacts: 5, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2013 20 05
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 6 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.237 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2013 29 05
M16 IP40 cable connector, Contacts: 5, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2013 29 05
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 6 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.237 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2017 20 05
M16 IP40 cable connector, Contacts: 5 (stereo), 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2017 20 05
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 6 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.231 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2021 20 06
M16 IP40 cable connector, Contacts: 6 DIN, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2021 20 06
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.449 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2021 29 06
M16 IP40 cable connector, Contacts: 6 DIN, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2021 29 06
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 250 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.466 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- The connector is not suitable for mains voltages. Please observe the pollution degrees and the overvoltage category. For further information refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2025 20 07
M16 IP40 cable connector, Contacts: 7, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2025 20 07
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 800 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.735 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2025 29 07
M16 IP40 cable connector, Contacts: 7, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2025 29 07
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 800 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.735 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To prevent the connector being opened unintentionally when used in electrical circuits containing hazardous life parts, the thread between the housing and the connector head must be secured using a suitable cyanoacrylate adhesive. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2061 20 08
M16 IP40 cable connector, Contacts: 8 DIN, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2061 20 08
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 5 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Ag (silver) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.93 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2061 29 08
M16 IP40 cable connector, Contacts: 8 DIN, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2061 29 08
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.75 mm² |
| Wire gauge (AWG) | 18 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 5 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.93 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2029 20 12
M16 IP40 cable connector, Contacts: 12, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2029 20 12
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 3 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.173 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2033 20 14
M16 IP40 cable connector, Contacts: 14, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2033 20 14
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 3 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.334 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2037 20 16
M16 IP40 cable connector, Contacts: 16, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2037 20 16
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 3 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.543 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2041 20 19
M16 IP40 cable connector, Contacts: 19, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2041 20 19
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 3 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.81 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 2045 20 24
M16 IP40 cable connector, Contacts: 24, 6.0 - 8.0 mm, shieldable, solder, IP40
M16, series 581, Miniature connectors
| Order number |
99 2045 20 24
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.14 mm² |
| Wire gauge (AWG) | 26 |
| Cable outlet | 6.0 - 8.0 mm |
| Degree of protection | IP40 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 1 A |
| Rated voltage | 60 V |
| Rated impulse voltage | 500 V |
| Pollution degree | 1 |
| Overvoltage category | I |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuZn (brass) |
| Contact plating | Au (gold) |
| Contact body material | PBT (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 28.268 |
Security notices
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
Contact to customer service
Do you have any questions regarding our products or do you wish an individual offer?