Ordering no:
Female angled connector, 360° EMC safe, shielded, cable outlet 3.5-5 mm
Female angled connector, 360° EMC safe, shielded, cable outlet 3.5-5 mm, Series 712
Available numbers of contacts
99 0402 75 02
M9 IP67 female angled connector, Contacts: 2, 3.5 - 5.0 mm, shieldable, solder, IP67
M9, series 712, Subminiature connectors
| Order number |
99 0402 75 02
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 3.5 - 5.0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 4 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | II |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuSn (bronze) |
| Contact plating | Au (gold) |
| Contact body material | PA (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 26.361 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 0406 75 03
M9 IP67 female angled connector, Contacts: 3, 3.5 - 5.0 mm, shieldable, solder, IP67
M9, series 712, Subminiature connectors
| Order number |
99 0406 75 03
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 3.5 - 5.0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 4 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | II |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuSn (bronze) |
| Contact plating | Au (gold) |
| Contact body material | PA (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 26.451 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 0410 75 04
M9 IP67 female angled connector, Contacts: 4, 3.5 - 5.0 mm, shieldable, solder, IP67
M9, series 712, Subminiature connectors
| Order number |
99 0410 75 04
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 3.5 - 5.0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 3 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | II |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuSn (bronze) |
| Contact plating | Au (gold) |
| Contact body material | PA (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 26.556 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 0414 75 05
M9 IP67 female angled connector, Contacts: 5, 3.5 - 5.0 mm, shieldable, solder, IP67
M9, series 712, Subminiature connectors
| Order number |
99 0414 75 05
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.25 mm² |
| Wire gauge (AWG) | 24 |
| Cable outlet | 3.5 - 5.0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 3 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | II |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuSn (bronze) |
| Contact plating | Au (gold) |
| Contact body material | PA (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 26.634 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 0422 75 07
M9 IP67 female angled connector, Contacts: 7, 3.5 - 5.0 mm, shieldable, solder, IP67
M9, series 712, Subminiature connectors
| Order number |
99 0422 75 07
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.14 mm² |
| Wire gauge (AWG) | 26 |
| Cable outlet | 3.5 - 5.0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 1 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | II |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuSn (bronze) |
| Contact plating | Au (gold) |
| Contact body material | PA (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 26.498 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
99 0426 75 08
M9 IP67 female angled connector, Contacts: 8, 3.5 - 5.0 mm, shieldable, solder, IP67
M9, series 712, Subminiature connectors
| Order number |
99 0426 75 08
|
| Connector locking system | screw |
| Termination | solder |
| Wire gauge (mm) | 0.14 mm² |
| Wire gauge (AWG) | 26 |
| Cable outlet | 3.5 - 5.0 mm |
| Degree of protection | IP67 |
| Mechanical operation | > 500 Mating cycles |
| Upper limit temperature | 85 °C |
| Lower limit temperature | – 40 °C |
| Rated current (40 °C) | 1 A |
| Rated voltage | 125 V |
| Rated impulse voltage | 1500 V |
| Pollution degree | 1 |
| Overvoltage category | II |
| Insulating material group | III |
| Volume resistivity | ≤ 3 mΩ |
| Insulation resistance | ≥ 10¹⁰ Ω |
| Contact material | CuSn (bronze) |
| Contact plating | Au (gold) |
| Contact body material | PA (UL 94 V-0) |
| Customs tariff number | 85369010 |
| Weight (g) | 26.55 |
Security notices
- The connector must not be connected or separated under load. Non-observance and incorrect use can result in personal injury.
- The connectors are designed for use in plant, control system and electrical equipment. The end user is responsible for checking whether the connectors are suitable for use in other applications.
- Connectors used in electrical circuits containing hazardous life parts must only be assembled and used by or under the supervision of persons with the requisite electrotechnical training, taking the applicable regulations and standards into account.
- Connectors with degree of protection IP 67 and IP 68 are not suitable for use under water. When used outdoors, the connectors must be separately protected against corrosion. For further information about IP degrees of protection refer to ‘Technical support’ in the Download Centre.
- To lock the cable connector to the equipment connector, the threaded ring is tightened until it is ‘finger-tight’ (approx. 50 cNm).
Contact to customer service
Do you have any questions regarding our products or do you wish an individual offer?